
Ducellier head ignition 65 mm for R5/R6/...CX/DS/...204/304...
Head for Ducellier lighter: Fitting inside the head = 65 mm, outside about 72 mm.For Renault R5/R6/R8/R10/R12/R15/R16/R20, Citroen CX/DS/ID/H/HY/HZ, Peugeot 204/304/306/404/504/j7
(20,42 € HT)
Aerosol gasket for cylinder head
Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)
(35,00 € HT)
Fuel gauge - replacement float
Float in synthetic material resistant to current fuels. Used to replace the cork floats on the fuel gauge Length: 1.40" Diameter: 1.14"
(17,72 € HT)
Shaft 8.5 mm Ø repair - repair Solex 32 PBIC carburettor or similar
Shaft dimension repair 8.5 mm with butterfly for repair carburettor Solex 32 PBIC or similarOverall length 91.5 mm
(22,00 € HT)
various repairs
(120,00 € HT)
Ignition - round head igniter Ducellier
Finger for igniter equipped with Ducellier round head
(12,10 € HT)
gasket for solex 32 pbic carburetor
2 x paper gaskets for Solex 32 pbi carburetor base.Fixing center distance: 60 mmCentral passage: 32 mmTotal length: 78 mmwidth: 50mm
(3,80 € HT)
Head gasket + 4 x manifold gaskets - Renaul NN
Includes:- 1x copper cylinder head gasket- 1 x 3-hole gasket for the manifold- 2 x small oval gaskets- 1 x large oval seal
(176,25 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
(9,00 € HT)
set of 2 spinnaker rings 32x55x10
(38,00 € HT)
oil scraper ring 66.04 thickness 5 mm
(38,00 € HT)
Aviation collex type paste gasket for cylinder head - 450ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
(35,00 € HT)
IGOL Rallye Gear axle transmission oil SAE 75 80 90 - GL4
Oil for gearbox and bridge for old mechanics. Type SAE 75 80 90 - GL4. 1L container.(Not suitable for Peugeot type screw axles)
(15,00 € HT)
Exhaust collar flange Ø 45mm
Flange for exhaust connection (clamp with caliper) Ø 45 mm
(7,50 € HT)
8 x sealed segments 53.50 mm thick 2mm + 4 x scraper segments without spring in 54.00 3mm thick
8 x sealed segments 53.50 mm thick 2mm + 4 x scraper segments without spring in 54.00 3mm thick
(88,50 € HT)
Viewed products
Peugeot 403 engine gaskets kit - 8 hp
Engine gaskets kit for Peugeot 403 - 8 hp - 80 mm boreHead gasket and base gaskets included.
(96,00 € HT)
set of 2 Peugeot D3 D4 windscreen seals
Set of 2 windscreen gaskets for Peugeot D3 or D4.
(100,00 € HT)
Peugeot accelerator cable403 (kit)
Kit for repairing the accelerator cable Peugeot 403 all models.
(15,00 € HT)
set of window slides for the 2 front doors - Peugeot D3 D4
Set of window sliders for Peugeot D3 or D4.
(48,00 € HT)
Ignition - round head igniter Ducellier
Finger for igniter equipped with Ducellier round head
(12,10 € HT)