Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
Front brake hose 328 mm - Citroen HY - June 1963 to end
FRONT brake hose for Citroen from June 1963 to end of series. The end caps are different from each other)Long 328 mm
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Brake line - Ø 4.5 mm - 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 4.5 mm.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Rear brake hose D 400mm - Citroen HY - from June 1963 to the end
Brake hose REAR RIGHT for Citroen from June 1963 to end: HZ HY HWLong 400 mm
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
Rear brake hose with double connections on pipe - 320 mm - Citroen HY - after 1970
Brake hose for Citroën HY. Model equipped with fittings allowing connection with rotating nut on rigid pipe on both sides. Often fitted after 1970 - Long 320 mm. Only for synthetic liquid (Dot 3, Dot 4). For use with LHM call us
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Adapter fitting 3/8 UNF Male - 10x100 female
Adapter fitting 3/8 UNF Male - 10x100 female
€20.40 TTC
(17,00 € HT)
(17,00 € HT)
Hose 7.5x13.5 - brake jar / master cylinder - 1ml - Synthetic liquid DOT 4
Hose sold by the meter for jar connection to master cylinder (7.5 mm plastic nipple connection) - 13.5 mm outsideDoes not withstand pressure. TYPE EPDM + textile reinforcement - intended only for synthetic fluid type DOT 4 - Not suitable for ...
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€4.67 TTC
(3,89 € HT)
(3,89 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
Brake reservoir with nipple + contact
Brake fluid reservoir, translucent plastic.With plug, fixing bracket and electrical contact for minimum liquid level
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Set of 4 front brake shoes 45 mm - HY or type H Citroen - until 02/1962
Set of 4 front brake shoes - standard exchange. (Send us your set before shipping the new one). High performance friction, applied by industrial bonding, no more rivets that damage the drums. Pickled and varnished brake shoes.
€134.90 TTC
(112,42 € HT)
(112,42 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€5.40 TTC
(4,50 € HT)
(4,50 € HT)
Brake limiter distributor - set of springs - Citroen HY type H
Spring set for brake distributor brake limiter Citroen HY type H
€29.90 TTC
(24,92 € HT)
(24,92 € HT)
