Adapter fitting 3/8 UNF Male - 10x100 female
Adapter fitting 3/8 UNF Male - 10x100 female
€21.00 TTC
(17,50 € HT)
(17,50 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
- New
copy of copper gasket kit for front brake cylinder (assembly with hollow screw 1/2) - Renault R2087 Goélette Prairie
Set of 2 seals for hollow screw and banjo (for 1 cylinder)
€4.08 TTC
(3,40 € HT)
(3,40 € HT)
Contactor: copper seal kit for LONG stop contactor 022114
Set of 2 seals for STOP LONG contactor
€3.60 TTC
(3,00 € HT)
(3,00 € HT)
Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€4.67 TTC
(3,89 € HT)
(3,89 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€5.40 TTC
(4,50 € HT)
(4,50 € HT)
Adapter connection 1/2 UNF female - 3/8 UNF male
Braking adapter 1 / 2-20 UNF female by 3/8 24 male threads
€11.88 TTC
(9,90 € HT)
(9,90 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€83.64 TTC
(69,70 € HT)
(69,70 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
€11.40 TTC
(9,50 € HT)
(9,50 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Set of 4 relined rear brake shoes - Renault SG2
Set of 4 rear brake shoes relined in standard exchange for Renault SG2. Microblasting, varnish, industrial bonding of friction. Strong adhesion. Eliminates the problem of rivets that could damage the drums. Shipping upon receipt of worn parts.
€216.00 TTC
(180,00 € HT)
(180,00 € HT)
Master cylinder inside piston 20mm - with brake assist - Renault Saviem Sg2
Single circuit master cylinder for SG2 Renault or Saviem from 1970 to end of series. Current product of French manufacture.
€155.40 TTC
(129,50 € HT)
(129,50 € HT)
Hose 7.5x13.5 - brake jar / master cylinder - 1ml - Synthetic liquid DOT 4
Hose sold by the meter for jar connection to master cylinder (7.5 mm plastic nipple connection) - 13.5 mm outsideDoes not withstand pressure. TYPE EPDM + textile reinforcement - intended only for synthetic fluid type DOT 4 - Not suitable for ...
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
3/8 - 24 f copper pipe fitting
Rigid brake line nut. 3/8 x 24 threads / inch. Tube Ø 4.75 mm
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
male female brake hose - 11.1 mm - 7/16 - Renault SG2
Female male brake hose - 520 mm - Renault SG2Vehicle with single circuit braking circuit: 3 MF hoses are requiredVehicle with dual circuit braking system: 3 MF hoses + 2 FF hoses are required
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
