
Brake line - from 100 to 150 cm
" Brake line remanufactured on request, only in copper diameter 6.35 mm. . Provide model (length and 2 original end caps) Shipment after receipt of your model. "
(51,70 € HT)
Rear right brake cylinder 28.5mm -Peugeot 403 L - utility - 07/56 at the end
RIGHT REAR wheel brake cylinder.403 Utility and LgasolineJul. 1956 =>End of series403 Diesel utilityOct. 1959 =>End of series403 L dieselNov. 1959 =>End of series
(53,50 € HT)

Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
(75,70 € HT)
Peugeot 403 truck 28.5mm rear cylinder required
" Front wheel cylinder repair kit, with pistons and spring. (For one wheel) Piston diameter = 28.57 mm "
(20,25 € HT)

Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
(39,70 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
(11,50 € HT)
7/16 banjo fitting + 7/16 hollow screw + seals
7/16 banjo fitting + 7/16 hollow screw + sealsDiameter male thread of the screw 11 mm
(27,35 € HT)
Adapter fitting 7/16 Male - 7/16 female outgoing cone
Adapter fitting 7/16 Male - 7/16 female outgoing cone
(16,30 € HT)
Brake switch - stop - DOT 3 and 4
" Brake switch. STOP light function - compatible with synthetic liquid type" "lockheed" "Dot 3 and 4. If using 100% silicone liquid: Choose this other reference 1/2 - 20 thread / inch thread "
(16,29 € HT)
Front brake cylinder - Kit of 4 pieces 28.5mm - Peugeot 403 ALL models
4 front brake cylinders kit - Ø 28.57 mm - 7/16 inlets - Peugeot 403 ALL modelsThe kit includes:- 2 upper FRONT cylinders- 2 lower FRONT cylindersFrench manufacturing - NON-CONTRACTUAL photo.
(212,00 € HT)

Brake reservoir with rubber
Translucent tank, delivered with bracket; rubber plug and fitting.
(32,00 € HT)
Master cylinder 25.4 mm Peugeot 403
Complete master cylinder D 25.4 mm. For Peugeot 403.Piston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screwsThere is also a 22 mm model, available on our store.
(54,00 € HT)

Rear brake cylinder 25.4mm - cone protruding - Peugeot 403
Rear wheel cylinder d 25.4mm, inclined pipe inlet 7/16. Exiting cone visible at the bottom of the liquid inlet on the cylinder.Non contractual photo.
(50,50 € HT)
