Rear right brake cylinder 28.5mm -Peugeot 403 L - utility - 07/56 at the end
RIGHT REAR wheel brake cylinder.403 Utility and LgasolineJul. 1956 =>End of series403 Diesel utilityOct. 1959 =>End of series403 L dieselNov. 1959 =>End of series
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Brake line - from 100 to 150 cm
" Brake line remanufactured on request, only in copper diameter 6.35 mm. . Provide model (length and 2 original end caps) Shipment after receipt of your model. "
€79.20 TTC
(66,00 € HT)
(66,00 € HT)
Peugeot 403 rear brake shoe set - 35 mm
Set of 4 rear brake shoes relined, in standard exchange. Peugeot 403 assembly. (Send us your set before shipping the new one)High performance friction, applied by industrial bonding, no more rivets that damage the drums. Pickled and varnished ...
€102.00 TTC
(85,00 € HT)
(85,00 € HT)
Contactor: copper seal kit for LONG stop contactor 022114
Set of 2 seals for STOP LONG contactor
€3.60 TTC
(3,00 € HT)
(3,00 € HT)
Adapter fitting 3/8 UNF Male - 10x100 female
Adapter fitting 3/8 UNF Male - 10x100 female
€19.20 TTC
(16,00 € HT)
(16,00 € HT)
Master cylinder 25.4 mm Peugeot 403 gasoline or diesel utility vehicles
Complete master cylinder D 25.4 mm. For Peugeot 403 petrol or diesel utility vehiclesPiston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screws
€62.40 TTC
(52,00 € HT)
(52,00 € HT)
7/16 banjo fitting + 7/16 hollow screw + seals
7/16 banjo fitting + 7/16 hollow screw + sealsDiameter male thread of the screw 11 mm
€33.54 TTC
(27,95 € HT)
(27,95 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.62 TTC
(8,85 € HT)
(8,85 € HT)
Brake hose 412 mm front Peugeot 403
Front brake hose for Peugeot 403 all models - Length 412 mm
€31.20 TTC
(26,00 € HT)
(26,00 € HT)
Lower front brake cylinder L or R 28.5 -Peugeot 403
Single piston cylinder without bleeder for front wheel - Peugeot 403 all models - Lower left or right mounting - French manufacture - (2 upper cylinders and 2 lower cylinders are needed to equip the front of a 403) - NON CONTRACTUAL photo.
€61.50 TTC
(51,25 € HT)
(51,25 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.24 TTC
(5,20 € HT)
(5,20 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
Adapter fitting 1/2 UNF Male - 1/2 UNF female with internal bicone
€18.00 TTC
(15,00 € HT)
(15,00 € HT)
