Rear brake cylinder 25.4 mm - Peugeot 403
Rear wheel cylinder repair kit, with pistons and spring. (For one wheel)Piston diameter = 25.4 mm
€21.85 TTC
(21,85 € HT)
(21,85 € HT)
Rear brake cylinder 25.4mm - cone protruding - Peugeot 403
Rear wheel cylinder d 25.4mm, inclined pipe inlet 7/16. Exiting cone visible at the bottom of the liquid inlet on the cylinder.Non contractual photo.
€50.50 TTC
(50,50 € HT)
(50,50 € HT)
Brake reservoir - male thread + electrical contact
Brake fluid reservoir, translucent plastic. With cap, and electrical contact for low fluid level
€39.50 TTC
(39,50 € HT)
(39,50 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
€9.50 TTC
(9,50 € HT)
(9,50 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€69.70 TTC
(69,70 € HT)
(69,70 € HT)
Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€75.70 TTC
(75,70 € HT)
(75,70 € HT)
Peugeot 403 truck 28.5mm rear cylinder required
" Front wheel cylinder repair kit, with pistons and spring. (For one wheel) Piston diameter = 28.57 mm "
€20.25 TTC
(20,25 € HT)
(20,25 € HT)
Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€3.89 TTC
(3,89 € HT)
(3,89 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€4.50 TTC
(4,50 € HT)
(4,50 € HT)
Lower front brake cylinder L or R 28.5 -Peugeot 403
Single piston cylinder without bleeder for front wheel - Peugeot 403 all models - Lower left or right mounting - French manufacture - (2 upper cylinders and 2 lower cylinders are needed to equip the front of a 403) - NON CONTRACTUAL photo.
€53.00 TTC
(53,00 € HT)
(53,00 € HT)
Adapter connection 7/16 male - 1/2 female
Adaptateur freinage mâle 7/16 (envion 11mm)femelle 11/16 pour recevoir gros flexible (17mm mâle
€15.00 TTC
(15,00 € HT)
(15,00 € HT)
Rear brake spring kit - Peugeot 403
Rear brake springs and clips kit - Peugeot 403
€32.00 TTC
(32,00 € HT)
(32,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€11.50 TTC
(11,50 € HT)
(11,50 € HT)
