Rear LEFT brake cylinder 28.5mm -Peugeot 403 L - utility - 07/56 at the end
LEFT REAR wheel brake cylinder.403 Utility and LgasolineJul. 1956 =>End of series403 Diesel utilityOct. 1959 =>End of series403 L dieselNov. 1959 =>End of series
€64.20 TTC
(53,50 € HT)
(53,50 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Adapter fitting 7/16 Male - 7/16 female outgoing cone
Adapter fitting 7/16 Male - 7/16 female outgoing cone
€19.56 TTC
(16,30 € HT)
(16,30 € HT)
Front brake cylinder - Kit of 4 pieces 28.5mm - Peugeot 403 ALL models
4 front brake cylinders kit - Ø 28.57 mm - 7/16 inlets - Peugeot 403 ALL modelsThe kit includes:- 2 upper FRONT cylinders- 2 lower FRONT cylindersFrench manufacturing - NON-CONTRACTUAL photo.
€254.40 TTC
(212,00 € HT)
(212,00 € HT)
Rear brake cylinder 25.4mm - cone protruding - Peugeot 403
Rear wheel cylinder d 25.4mm, inclined pipe inlet 7/16. Exiting cone visible at the bottom of the liquid inlet on the cylinder.Non contractual photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€4.67 TTC
(3,89 € HT)
(3,89 € HT)
Rear brake spring kit - Peugeot 403
Rear brake springs and clips kit - Peugeot 403
€14.96 TTC
(14,96 € HT)
(14,96 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Brake reservoir with nipple + contact
Brake fluid reservoir, translucent plastic.With plug, fixing bracket and electrical contact for minimum liquid level
€48.00 TTC
(40,00 € HT)
(40,00 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
€11.40 TTC
(9,50 € HT)
(9,50 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€83.64 TTC
(69,70 € HT)
(69,70 € HT)
Lower front brake cylinder L or R 28.5 -Peugeot 403
Single piston cylinder without bleeder for front wheel - Peugeot 403 all models - Lower left or right mounting - French manufacture - (2 upper cylinders and 2 lower cylinders are needed to equip the front of a 403) - NON CONTRACTUAL photo.
€63.60 TTC
(53,00 € HT)
(53,00 € HT)
Viewed products
Rear brake cylinder 25.4 mm - Peugeot 403
Rear wheel cylinder repair kit, with pistons and spring. (For one wheel)Piston diameter = 25.4 mm
€26.22 TTC
(21,85 € HT)
(21,85 € HT)
Bearings for Simca Versailles Chambord 030 - 52.53 mm
" Set of bearings for Simca Versailles, Chambord, Ariane 8 etc. V8 engine" "Aquilon" ". (1 rear landing + 2 front and central single landings) Dimension: 030 US (0.75 mm) "
€378.00 TTC
(315,00 € HT)
(315,00 € HT)
Bearings - set of 2 side shims - Simca Versailles Chambord STD
Set of 2 crankshaft shims Simca Versailles, Chambord, Ariane 8 etc. "Aquilon" V8 engine.You need 2 sets per motor
€342.00 TTC
(285,00 € HT)
(285,00 € HT)
Kit 3 camshaft bushes x 3 - Simca Versailles Chambord - Aquilon engine
Set of 3 camshaft bushes standard dimension for Aquilon Simca Versailles Chambord engine.Delivered with the tool.
€312.00 TTC
(312,00 € HT)
(312,00 € HT)
Front brake cylinder rebuild kit Ø 28.5 mm - PEUGEOT 403
Necessary reconditioning for 1 front wheel cylinder. Diameter 28.57 mm
€24.42 TTC
(20,35 € HT)
(20,35 € HT)
