Flexible rear brake hose 349 mm Simca Versailles Chambord Ariane
Flexible rear brake hose 349 mm long. Male ext 9mm - female int Ø 8.3 mm. Don't forget to replace the copper gasket: click here a> (The vehicle has only 1 rear flexible) - Simca Beaulieu, Chambord, Présidence, Marly 2, Ariane 4 and ...
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
Front brake cylinder rebuild kit Ø 28.5 mm - Ford Vendome - Simca Chambord
Necessary repair for 1 front wheel cylinder.
€24.42 TTC
(20,35 € HT)
(20,35 € HT)
Front brake cylinder Ø 28.5 mm - set of 4 - Simca Ariane
Set of 4 front brake cylinders. - Simca Ariane 4 and Ariane 8 - Simca 1300 until September 1965Includes: one cylinder with left bleeder, one with right bleed and two cylinders without bleed.Liquid entry 3/8Diameter 28.57 mm
€261.60 TTC
(218,00 € HT)
(218,00 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Rear brake cylinder L Ø 23.81 mm - incoming cone - Simca Ariane
Rear wheel cylinder. Left or Right Mount - Simca Ariane 4 and Ariane 8.Diameter: 23.81 mm - Version with cone entering the bottom of the thread at the liquid inlet. See detail photo.Please note that there is also a diameter of 18 or 19 mm.
€61.50 TTC
(51,25 € HT)
(51,25 € HT)
Brake hose 367 mm - front or rear - Simca 1300
Front or rear brake hose length 367 mm.Male ext 9mm - female int Ø 8.3 mmMounts on:- Simca 1300 front or rear- Simca 1500 rear onlyCheck with your model before ordering.
€26.40 TTC
(22,00 € HT)
(22,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Rear brake cylinder rebuild kit 19mm - Simca Chambord
" Complete overhaul kit for a rear wheel cylinder. Diameter: 23.81 mm "
€24.00 TTC
(20,00 € HT)
(20,00 € HT)
3/8 - 24 f copper pipe fitting
Rigid brake line nut. 3/8 x 24 threads / inch. Tube Ø 4.75 mm
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
22mm master cylinder kit Simca Versailles Chambord
Complete overhaul kit for 22 mm master cylinder.
€31.20 TTC
(26,00 € HT)
(26,00 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
