Special brake grease tube - 5g

Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.

Front wheel cylinder DYna Z Panhard - 1954 until June 1958 - d 31.75 mm

Rear wheel cylinder Dyna Z Panhard - May 1955 to June 1958 - d 22 mm

€70.80 TTC
(59,00 € HT)

Copper pipe fitting 7/16 - ext thread 11mm

Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm

Copper gasket 13.1 x 17

Copper gasket 13.1 x 17 mm thickness 1mm

€1.80 TTC
(1,50 € HT)

FRONT LEFT 28.5mm brake cylinder - Panhard PL 17 - Record mounting - 04/62 and fin

Front wheel cylinder L PL 17 - Record mounting - 04/62 and fine - d 28.57 mm. Left mounting.64 mm long - inside liquid passage = 10 mm

€66.00 TTC
(55,00 € HT)

Special brake grease tube - Plastilub ATE - 75 ml

Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!

Master cylinder 25.4 mm - Panhard Dyna Z

Complete master cylinder (piston d 25.4 mm). Fits Dyna Z 1954 thru June 1958.Piston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screws

€62.40 TTC
(52,00 € HT)

FRONT LEFT 28.5mm brake cylinder - Panhard PL 17 - 60 a 62

Front wheel cylinder L PL17 from 1960 to March 62 - d 28.57 mm. Entry 3/8 - Left side mounting. Length 72 mm - inside liquid passage = 8.5 mm

€81.60 TTC
(68,00 € HT)

Brake line - from 100 to 150 cm

" Brake line remanufactured on request, only in copper diameter 6.35 mm. . Provide model (length and 2 original end caps) Shipment after receipt of your model. "

Copper gasket 12 x 18 mm

Copper gasket 12 x18 x  1.5mm thick

€1.80 TTC
(1,50 € HT)

Copper gasket 10 x 18

Copper gasket 18x10 mm thickness 1mm

€1.92 TTC
(1,60 € HT)

Set of 4 relined REAR brake shoes - Panhard

Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...

€117.60 TTC
(98,00 € HT)

Ecrou

Male connector 12x100 on 6.35 mm pipe

Male connector 12x100 on 6.35 mm pipe

1/2 female 20 UNF connection on 8 mm tube (metal brake jar)

Metal tank foot nut (female 1/2 and d 8mm)

Copper gasket 13.1 x 18

Copper gasket 13.1 x 18 mm thickness 1mm

€1.92 TTC
(1,60 € HT)