Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€4.67 TTC
(3,89 € HT)
(3,89 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€76.44 TTC
(63,70 € HT)
(63,70 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€5.40 TTC
(4,50 € HT)
(4,50 € HT)
Peugeot 403 rear brake shoe set - 35 mm
Set of 4 rear brake shoes relined, in standard exchange. Peugeot 403 assembly. (Send us your set before shipping the new one)High performance friction, applied by industrial bonding, no more rivets that damage the drums. Pickled and varnished ...
€102.00 TTC
(85,00 € HT)
(85,00 € HT)
Rear brake cylinder 25.4mm - cone protruding - Peugeot 403
Rear wheel cylinder d 25.4mm, inclined pipe inlet 7/16. Exiting cone visible at the bottom of the liquid inlet on the cylinder.Non contractual photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Master cylinder 25.4 mm Peugeot 403 gasoline or diesel utility vehicles
Complete master cylinder D 25.4 mm. For Peugeot 403 petrol or diesel utility vehiclesPiston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screws
€64.80 TTC
(54,00 € HT)
(54,00 € HT)
Male thread brake reservoir
Brake fluid reservoir. Supplied with bracket, plug and 3/4 male connector 16 threads / p. External thread diameter = 18.5 mm. Delivered without caliper (fixing by the thread on the master cylinder). Lockeed and silicone compatible
€42.00 TTC
(35,00 € HT)
(35,00 € HT)
Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
7/16 banjo fitting + 7/16 hollow screw + seals
7/16 banjo fitting + 7/16 hollow screw + sealsDiameter male thread of the screw 11 mm
€32.82 TTC
(27,35 € HT)
(27,35 € HT)
Master cylinder Ø 25.4 mm - Peugeot 403
Repair kit for Ø 25.4 mm master cylinder
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Front upper brake cylinder L or R 28.5mm - Peugeot 403
Single piston cylinder with bleeder for front wheel - Peugeot 403 all models - Ø 28.57 mm. Upper left or right mounting - (2 upper cylinders and 2 lower cylinders are needed to equip the front of a 403) - NON CONTRACTUAL photo.
€61.50 TTC
(51,25 € HT)
(51,25 € HT)
Viewed products
Banjo adapter for master cylinder 18mm
" Adapter allowing to connect the inlet of a master cylinder in 18 mm on the original tube which goes to the jar. When the old models are in diam. 22mm, the adapter is essential to connect the tube coming from from the jar. The set consists of: 2 ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Front brake cylinder type G - Ford Anglia
Front wheel cylinder type G - Sold individually. (The photo allows you to recognize the model - a white letter is written on the part). You need one cylinder type G and one type D per front wheel.
€22.56 TTC
(22,56 € HT)
(22,56 € HT)
