Bearing bearings dimension 49.50 mm (0.50) - Citroen Traction HY U23
Bearing bearings dimension 49.50 (0.50) -Citroen:- Traction Perfo and 11D - HY until 1963 ("Traction" type engine)- U23
(398,00 € HT)
Ignition finger igniter Ducellier 65mm
Finger for Ducellier distributor equipped with a 65mm headMounts with Ducellier 65 mm head
(11,25 € HT)
seals x 8 fit to valve Ø 9 mm - H72 / 78 Citroen HY 63 and more
8 joint queue de soupape Ø 9mm - Citroen HY, type H, HW moteur type ID 19.Photo non contractuelle
(36,00 € HT)
Cartridge air filter - Citroen HY before 1963
Cartridge air filter - Citroen HY before 1963Dimensions on the photo
(21,58 € HT)
Axle 8.5 mm Ø repair - without butterfly - Solex 32 PBIC or similarsimilar
Shaft dimension repair 8.5 mm without butterfly for repair carburettor Solex 32 PBIC or similarOverall length 91.5 mm
(14,13 € HT)
Set of 3 25mm pellets for cast iron cylinder head - Citroen Traction U23 HY
Set of 3 Ø25mm pellets only for cast iron cylinder head - Citroen Traction U23 HY
(11,00 € HT)
Ignition head Ducellier 65 mm
Head for Ducellier distributor: Interlocking inside the head = 65 mm, outside about 72 mm.To be assembled with breakers 1 237 013 808, and ducellier finger.
(20,42 € HT)
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
(22,50 € HT)
Clutch mechanism type 1 Citroen HY
Clutch mechanism reconditioned, in standard exchange. Fitted on Citroen HY, type H, cast iron cylinder headComplete disassembly, micro balling, surfacing and retaring of the pressure plate.(The sending is done after receipt of the used mechanism, ...
(420,00 € HT)
Citroen U23 HY 11D engine kit cast iron cylinder head
Engine seal kit for Citroen U23, HY, equipped with 11D engine (cast iron cylinder head). The cylinder head gasket is slightly different from that of the 11D engine for Traction (reverse water pump). See detail of the cylinder head gasket on the ...
(225,00 € HT)
Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
(4,83 € HT)
Carburetor similar to the Solex 32 PBIC type
New carburettor similar to the Solex 32 PBIC model with accelerator pump. Vacuum outlet on foot base. Depending on the vehicle model, you will need to reset the configuration with the old starter, jets, cap or cover and throttle control
(163,07 € HT)
Echappement sangle support renforcé 50 mm
Sangle de suspension pour échappement, caoutchouc armé. entraxe 52 mm pour vis M8 mm.
(9,03 € HT)
Citroen HY lower hose WITHOUT heating after 07/63
Lower hose without heating flow after 07/1963
(32,00 € HT)