Reinforced collar for exhaust - Ø 44-47 mm
Reinforced collar for exhaust - Ø 44-47 mmRobust French manufacturing
€5.80 TTC
(4,83 € HT)
(4,83 € HT)
Clutch mechanism type 1 Citroen HY
Clutch mechanism reconditioned, in standard exchange. Fitted on Citroen HY, type H, cast iron cylinder headComplete disassembly, micro balling, surfacing and retaring of the pressure plate.(The sending is done after receipt of the used mechanism, ...
€600.00 TTC
(500,00 € HT)
(500,00 € HT)
Ignition silicon harness for Citroen HY or DS Traction U23 HY engine
Ignition harness (5 wires) for Citroën HY or ID - DS engine. Highly recommended with electronic ignition.Wire with red silicone insulator, works with platinum screws or electronic ignition, current manufacture (not from old stocks).Use the 4 ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Ignition harness - 1963 and up - Citroen HY engine H72 or H78 (ID19)
Ignition harness (5 wires) for Citroën HY engine H72 or H78, DS 19 ID 19. Highly recommended with electronic ignition.Wire with red insulation, works with platinum screws or electronic ignition, current manufacture (not from old stocks).
€34.80 TTC
(29,00 € HT)
(29,00 € HT)
Citroen U23 HY engine kit cast iron cylinder head
Engine seal kit for Citroen U23, HY, equipped with 11D engine (cast iron cylinder head). The cylinder head gasket is slightly different from that of the 11D engine for Traction (reverse water pump). See detail of the cylinder head gasket on the ...
€420.00 TTC
(350,00 € HT)
(350,00 € HT)
Ignition coil 6V - High Performance
Bosch, NGK or Béru High Performance type ignition coil, guaranteed for use with:- 6 V platinum-plated screw igniter (breakers),- electronic ignition type 123 ignition,- platinum screw igniter + electronic amplification module
€84.00 TTC
(70,00 € HT)
(70,00 € HT)
Reinforced collar for exhaust - Ø 64-67 mm
Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
Axe 8 mm avec papillon pour réparation carburateur Solex 32 PBIC ou similaire
€26.40 TTC
(22,00 € HT)
(22,00 € HT)
Double pressure gauge holder
Metal support, black lacquered for standard manometer D52 mm. Ready to fix.
€12.00 TTC
(10,00 € HT)
(10,00 € HT)
Set of 4 30mm pellets for cast iron cylinder head - Citroen Traction U23 HY
Set of 4 Ø30mm pellets only for cast iron cylinder head - Citroen Traction U23 HY
€24.00 TTC
(20,00 € HT)
(20,00 € HT)
Fuel gauge - replacement plastic float
White plastic float. Used to replace ring gauge floats.
€15.00 TTC
(12,50 € HT)
(12,50 € HT)
Jeu palier 0.50 ligne d'arbre - Citroen Traction 15/6
€1,416.00 TTC
(1 180,00 € HT)
(1 180,00 € HT)
Viewed products
Peugeot 203 front hub kit - 1st generation
Kit for 1 front hub Peugeot 203 - 1st generation including 2 well-known brand bearingsDim 20 x 52 width 15 mmDim 25 x 62 width 17 mmWarning: check that these dimensions correspond to your vehicle before ordering - Kit for a single wheel.
€40.00 TTC
(33,33 € HT)
(33,33 € HT)
Front brake cylinder 22 mm - Renault 4CV - 02/53 to 01/1956
Front brake cylinder 22 mm - Renault 4CV - 02/53 to 01/1956
€63.79 TTC
(53,16 € HT)
(53,16 € HT)
Rear brake cylinder 19 mm - Renault 4CV - 02/53 to 01/1956
Rear brake cylinder 19 mm - Renault 4CV - 02/53 to 01/1956
€63.60 TTC
(53,00 € HT)
(53,00 € HT)
Rear brake hose - Renault 4cv - feb / 53 to end
Rear brake hose - Renault 4cv - feb / 53 to end
€24.00 TTC
(20,00 € HT)
(20,00 € HT)
Peugeot 203 front hub kit - 2nd generation
Kit for 1 front hub Peugeot 203 - 2nd generation including 2 bearings and a sealing ring - brand bearings (no remanufacturing unknown)Dim 20 x 52 width 15 mmDim 30 x 62 width 16 mmWarning: check that these dimensions correspond to your generation ...
€163.20 TTC
(136,00 € HT)
(136,00 € HT)
Crankshaft bearing screws Ford 49 to 52
Set of bearing screws for V8 Ford Vedette model 1949 to 1952
€134.42 TTC
(134,42 € HT)
(134,42 € HT)
Peugeot 203 lower hose before 05/55
Lower hose before 05/1955. For Peugeot 203. (diam 40mm approximate overall length 27cm)
€32.40 TTC
(27,00 € HT)
(27,00 € HT)
