- New
Reinforced collar for exhaust - Ø 64-67 mm
Reinforced collar for exhaust - Ø 64-67 mmRobust French manufacturing
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
IGOL 20W50 mineral oil - 5L can
5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...
€36.00 TTC
(30,00 € HT)
(30,00 € HT)
Pellet - set of 4 - Ford Vedette cylinder heads
Set of 4 18.4 mm pellets for Ford Vedette cylinder heads
€28.00 TTC
(28,00 € HT)
(28,00 € HT)
Battery switch - safety
Battery isolator - used to electrically isolate the battery. To be placed on a terminal of the battery.
€12.00 TTC
(10,00 € HT)
(10,00 € HT)
Head gasket 2 mm solid copper Ford Vedette
Solid copper cylinder head gasket. 2mm thickness. Used with planed cylinder head. Tightening to 5m.kg. Mandatory installation with aerosol sealant, available here a>. Measured cylinder head thickness Head gasket type 37.3 mm ...
€160.40 TTC
(160,40 € HT)
(160,40 € HT)
Clutch mechanism Ford Vedette
Clutch mechanism reconditioned, in standard exchange mounted on Ford Vedette, Abeille, Comète, Monte Carlo, Vendôme engine Complete disassembly, micro balling, surfacing and retaring of the pressure plate. (The sending is done after receipt ...
€354.00 TTC
(295,00 € HT)
(295,00 € HT)
Ford Vedette oil pump pinion
Replacement gear for oil pump - V8 Ford Vedette. Supplied with 4 rivets. (Advantageously replaces the celoron one that has become fragile over time)Attention for the V8 Simca 13 hp 2350 cm3, choose the reference "Simca oil pump pinion" on our shop.
€187.00 TTC
(187,00 € HT)
(187,00 € HT)
Head gasket 3 mm solid copper Ford Vedette
Solid copper cylinder head gasket. Thickness 3mm. Used with very planed cylinder head.Tightening at 5m.kg. Pose impérative avec le produit d'étanchéité en pâte pour les joint de culasse 2 ou 3 mm disponible ici.Cylinder head thickness measured ...
€192.40 TTC
(192,40 € HT)
(192,40 € HT)
Ford Vedette cylinder head bolt set
Set of 34 hexagon head screws to replace the original studs - 3/8 16f / p unc 2 lengths of screws in the set - Allows easy removal of cylinder heads. Tightening 5 m.kg maximum
€155.20 TTC
(155,20 € HT)
(155,20 € HT)
Aviation collex type paste gasket for cylinder head - 117ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
€41.22 TTC
(34,35 € HT)
(34,35 € HT)
V8 Ford Vedette Simca Versailles Chambord oil filter cartridge
Replacement cartridge for Ford Vedette, Vendôme and Simca Vedette oil filters. Identical to the C4 FRAM model. Info: Delivered without the gasket under the bell (or the cover for the Simca). It is for sale separately: click HERE
€13.44 TTC
(11,20 € HT)
(11,20 € HT)
Ford Vedette COTAL disc clutch 215 mm
Clutch disc reconditioned, (exchange) - fit to Ford Vedette. Complete disassembly, micro balling and painting. (The sending is done after receipt of the used mechanism, not destroyed)(Depending on the year, non-contractual photo)
€144.00 TTC
(120,00 € HT)
(120,00 € HT)
Ford Vedette air filter + breather sticker
" Sticker for air filter and breather cap. Mounts on Ford V8 Vedette, Vendôme, Cometer, Monte Carlo etc. Sticker "
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Bearing 6203 - 17x40x12
Bearing - 17x40x12 waterproof (often used on dynamo, water pump, flywheel center, etc.). Check with the dimensions of your bearing.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Set of 8 pistons 66.50 Ford Vedette
Set of 8 pistons - New manufacture, similar to the original model - reduction in piston mass (approximately 255 gr with rings) - molybdenum treatment - cylinder dimension 66.50 mm. Supplied with segments, pins and circlips - The segments supplied ...
€1,548.00 TTC
(1 290,00 € HT)
(1 290,00 € HT)
Viewed products
Temperature manometer with probe - ivory background
Mano "OS" temperature indicator (without electrical connection). Direct reading by probe mounted on a radiator hose (high outlet). 52 mm recess on the pressure gauge side.Capillary 1m80. Delivered with lighting and probe for the hose.
€78.00 TTC
(65,00 € HT)
(65,00 € HT)
