Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
Rubber teat end for brake reservoir
" Flexible connection for brake reservoir. (100% rubber compatible with lockheed and silicone) Must be fitted with the metal insert to prevent tearing and accidental emptying of the liquid reservoir. "
€11.40 TTC
(9,50 € HT)
(9,50 € HT)
- New
copy of copper gasket kit for front brake cylinder (assembly with hollow screw 1/2) - Renault R2087 Goélette Prairie
Set of 2 seals for hollow screw and banjo (for 1 cylinder)
€4.08 TTC
(3,40 € HT)
(3,40 € HT)
Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€90.84 TTC
(75,70 € HT)
(75,70 € HT)
Set of 4 front brake shoes 203 Utility U8 Peugeot
Set of 4 front brake shoes - width 52 mm - standard exchange. (Send us your set before shipping the new one). High performance friction, applied by industrial bonding, no more rivets that damage the drums. Pickled and varnished brake shoes.
€152.40 TTC
(127,00 € HT)
(127,00 € HT)
Rear brake cable - long 154 Left or Right - Peugeot 203
Handbrake cable for left or right rear wheel - Long 154 cm - Saloon 203 C 1954 - 60(2 cables are needed per vehicle)
€30.00 TTC
(25,00 € HT)
(25,00 € HT)
1/2 female 20 UNF connection on 8 mm tube (metal brake jar)
Metal tank foot nut (female 1/2 and d 8mm)
€11.10 TTC
(9,25 € HT)
(9,25 € HT)
Pipe connector 1/2 20 UNF - tube 6.35 mm - external thread 12.5 mm
Rigid brake line nut. 1 / 2-20 UNF or Ø 12.5 mm - drilling for 6.35 mm tube (1/4 p)
€5.40 TTC
(4,50 € HT)
(4,50 € HT)
Adapter fitting 7/16 Male - 7/16 female outgoing cone
Adapter fitting 7/16 Male - 7/16 female outgoing cone
€19.56 TTC
(16,30 € HT)
(16,30 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
Pipe connection 1/2 20 UNF - 8 mm tube - special jar - 12.5 mm thread ext.
Rigid brake line nut. 1 / 2-20 UNF i.e. Ø 12.5 mm - drilling for 8 mm tube special brake reservoir
€6.18 TTC
(5,15 € HT)
(5,15 € HT)
Brake pipe - from 250 to 300 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€83.64 TTC
(69,70 € HT)
(69,70 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
