Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€90.84 TTC
(75,70 € HT)
(75,70 € HT)
Brake line - from 150 to 200 cm
Brake line re-manufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original end pieces)Shipping after receiving your model.
€69.24 TTC
(57,70 € HT)
(57,70 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
FRONT RIGHT 28.5mm brake cylinder - Panhard PL 17 - 60 to 62
Front wheel cylinder L PL17 from 1960 to March 62 - d 28.57 mm. Entry 3/8 - Right mounting. Length 72 mm - inside liquid passage = 8.5 mm
€84.00 TTC
(70,00 € HT)
(70,00 € HT)
Rear brake cylinder 19mm - 3/8 Panhard 24 - 07/1964 to end
Rear wheel cylinder 19mm - Panhard 24 équipé frein à tambours - 07/1964 à fin de série
€69.12 TTC
(57,60 € HT)
(57,60 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Set of 4 relined brake shoes Panhard Dyna x86
Set of 4 relined brake shoes (front or rear) 195 mm x 30 mm in standard exchange for Panhard Dyna X86, Dyna Z, PL 17 and series 24Microblasting, varnish, industrial bonding of friction. Strong adhesion.Eliminates the problem of rivets that could ...
€138.00 TTC
(115,00 € HT)
(115,00 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€76.44 TTC
(63,70 € HT)
(63,70 € HT)
Special brake grease tube - 5g
Tube of special braking grease (5gr), Lockheed DOT and silicone compatible, protects steel cylinder and piston parts, helps them slide, compatible with rubber parts.
€4.67 TTC
(3,89 € HT)
(3,89 € HT)
Front brake hose 470 mm male 7/16 - Panhard PL 17
Front brake hose PL17 from 1960 to end of series. Male thread 7/16 (11.1 mm) - length 470 mm
€33.00 TTC
(27,50 € HT)
(27,50 € HT)
