
Calibrouge (Plastigage) mechanical clearance measurement
"Plastigage"The Calibrouge ("plastigage or plastigauge") is a simple and practical tool for measuring the clearances of your bearings. Range of use: operating clearance from 0.025 to 0.175 mm
(22,50 € HT)
Standard 6V coil ignition
Branded ignition coil guaranteed for use with 6 V platinum-plated igniter (breakers). Impedance respected to prevent the breakers from becoming blue. Also works perfectly with electronic module or integral electronic igniter.
(36,00 € HT)
Set Segments Ø 58.00 2x2x3 - Rosengart LR (set of 12)
Set of 16 segments (4 per piston) for LR2, LR4, LR4N2 engines and derivatives. Bore 58. Attention in case of error on your part, these products cannot be taken back.- 8 x compression h 2mm- 4 x scraper h 3 mmContact us for other sizes.
(150,98 € HT)
Aviation collex type paste gasket for cylinder head - 450ml
Sealing paste to be applied on both sides of a cylinder head gasket. Product similar to "Collex". Leave to evaporate for about 30 min at room temperature after application, then fit the gasket - improves the seal - recommended with solid copper ...
(35,00 € HT)
IGOL semi-synthetic 15W50 oil - 5L can
Can of 5 L.Viscosity: 15W-50BenefitsHéRITAGE ZS semi-synthetic oil.Multigrade lubricant for gasoline engine of tourism, reinforced with synthetic bases, particularly adapted to the old engines, gasoline or diesel, equipped with an oil filter - ...
(35,00 € HT)
Rosengart crankshaft front bearing
Double row ball bearing, front crankshaft bearing assembly (timing side) for LR2, LR4, LR4N2 engines and derivatives.
(110,00 € HT)
Aerosol gasket for cylinder head
Sealing spray varnish to be sprayed on both sides of a cylinder head gasket. Improves sealing, essential with solid copper gaskets (any thickness)
(35,00 € HT)
Exhaust support strap reinforces 90 mm
Suspension strap for exhaust. Robust construction, reinforced rubber, metal eyelets.92 mm center distance for M8 mm screws.
(13,48 € HT)
Set 4 Pistons 56.50 - axle 16 mm - Rosengart LR
Set of 4 pistons for Rosengart LR2, LR4, LR4N2, and derivatives. Current manufacture - Bore 56.00 - 56.50 - 57.00 - 57.50 - 58.00 mm For 12 mm or 16 mm axle (to be specified when ordering). Supplied with axles, segments, circlips. Possibility of ...
(1 080,00 € HT)
IGOL 20W50 mineral oil - 5L can
5 l can (non contractual photo) - Viscosity: 20W-50BenefitsHéRITAGE GTZ mineral oil.Multigrade lubricant for Gasoline and Diesel engines, made from severely refined mineral bases and additives suitable for older engines. The anti-wear additive ...
(30,00 € HT)
12v to 6v regulator for temperature, pressure, fuel gauge
This module allows the use of 6V pressure gauges on a 12V vehicle (negative to ground). Mounts on a temperature gauge, pressure, fuel gauge, ...Very practical, it is fixed directly on the supply terminal of the pressure gauge thanks to a hole ...
(30,00 € HT)
Segment set Ø 56.50 2x2x3 - Rosengart LR (set of 12) - Need to adjust gap before to use
You need to adjust gap before to place in each cylinder Set of 12 rings - fit to LR2, LR4, LR4N2 engine Ø 56.50 (somme are 57 mm) - 8 x compression hauteur 2mm - 4 x racleur hauteur 3 mm Attention certains segments sont livrés en Ø 57 mm . ...
(98,00 € HT)
Set Segments Ø 56.50 2.5x2.5xscraper 2.5xscraper .5 - Rosengart LR (set of 16)
Set of 16 segments (4 per piston) for LR2, LR4, LR4N2 engines and derivatives. Bore 56.50- 4 x fire segment h 2.5mm- 4 x compression h 2.5mm- 8 x scraper h 2.5 mmPlease note that the scrapers are Ø 56.84 mm. Review the game at the cupContact us ...
(125,00 € HT)
Viewed products
Segment set Ø 57.50 2x2x3.5x3.5 - Rosengart LR (set of 16)
" Set of 16 segments (4 per piston) for LR2, LR4, LR4N2 and derivatives. Bore 57.50 - 2 x compression h 2mm - 2 x scraper h 3.5 mm Contact us for other dimensions. "
(199,17 € HT)