Rear brake cylinder 25.4 mm - Ford Vedette
" Rear wheel cylinder repair kit, with pistons and spring. (For one wheel) Piston diameter = 25.4 mm "
€26.22 TTC
(21,85 € HT)
(21,85 € HT)
Rear brake cylinder 25.4 mm - 1949-53 Ford Vedette
Rear wheel cylinder d 25.4mm, Ford Vedette (1949 to August 1953), Vendôme, Comète, Monté Carlo, Abeille. Right pipe entry. NON-CONTRACTUAL photo.
€52.20 TTC
(43,50 € HT)
(43,50 € HT)
Brake pipe - from 300 to 350 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€90.84 TTC
(75,70 € HT)
(75,70 € HT)
Brake line - from 200 to 250 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Provide model (length and 2 original tips)Shipping after receipt of your model.
€76.44 TTC
(63,70 € HT)
(63,70 € HT)
Adapter fitting 3/8 UNF Male - 10x100 female
Adapter fitting 3/8 UNF Male - 10x100 female
€21.00 TTC
(17,50 € HT)
(17,50 € HT)
Pipe Ø 8 mm from reservoir to master cylinder - 1 m
Brake line remanufactured upon request, exclusively in 8 mm diameter copper.Photo not contractually binding. Supplied WITHOUT fittings - you can order the one you need from our store (for the master cylinder side). The other end is bare (inlet on ...
€50.40 TTC
(42,00 € HT)
(42,00 € HT)
copy of Set of 4 Ford Vedette rear jaws - 1954
Set of 4 rear brake shoes in standard exchange. (Send us your set before shipping the new one) High performance friction, applied by industrial gluing, no more rivets which damage the drums. Pickled and varnished jaws.
€158.40 TTC
(132,00 € HT)
(132,00 € HT)
Front brake cylinder 31.7 mm - Ford Vedette 54 and Abeille
Front wheel cylinder d 31.75 mm - Ford Commercial Vedette type Abeille and some Vedette 1954. (Check your model carefully before ordering).
€53.40 TTC
(44,50 € HT)
(44,50 € HT)
3/8 - 24 f copper pipe fitting
Rigid brake line nut. 3/8 x 24 threads / inch. Tube Ø 4.75 mm
€7.80 TTC
(6,50 € HT)
(6,50 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
Brake reservoir with rubber
Translucent tank, delivered with bracket; rubber plug and fitting.
€38.40 TTC
(32,00 € HT)
(32,00 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
