Brake line - from 51 to 99 cm
Brake line remanufactured on request, only in copper diameter 6.35 mm. Large model, length from 50 cm, max 2m. Provide model (length and 2 original tips)Shipping after receiving your model.
€54.84 TTC
(45,70 € HT)
(45,70 € HT)
Copper pipe fitting 7/16 - ext thread 11mm
Rigid brake line nut. 7/16 or about 11 mm measured on the external thread and Ø hole for the tube = 6.35mm
€6.36 TTC
(5,30 € HT)
(5,30 € HT)
Raccord adaptateur 1/2 UNF mâle - 3/8 UNF femelle
Adaptateur freinage 1/2-20 UNF mâle par 3/8 24 filets femelle
€12.60 TTC
(10,50 € HT)
(10,50 € HT)
Master cylinder 25.4 mm Peugeot 403 gasoline or diesel utility vehicles
Complete master cylinder D 25.4 mm. For Peugeot 403 petrol or diesel utility vehiclesPiston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screws
€64.80 TTC
(54,00 € HT)
(54,00 € HT)
Brake switch - stop - DOT 3 and 4
" Brake switch. STOP light function - compatible with synthetic liquid type" "lockheed" "Dot 3 and 4. If using 100% silicone liquid: Choose this other reference 1/2 - 20 thread / inch thread "
€19.55 TTC
(16,29 € HT)
(16,29 € HT)
Metal insert tip for jar
Metal fitting to be fitted with the brake reservoir rubber to prevent the tearing and accidental draining of the brake fluid reservoir.
€10.80 TTC
(9,00 € HT)
(9,00 € HT)
Peugeot 403 truck 28.5mm rear cylinder required
" Front wheel cylinder repair kit, with pistons and spring. (For one wheel) Piston diameter = 28.57 mm "
€24.30 TTC
(20,25 € HT)
(20,25 € HT)
Contactor: copper seal kit for LONG stop contactor 022114
Set of 2 seals for STOP LONG contactor
€3.60 TTC
(3,00 € HT)
(3,00 € HT)
Front upper brake cylinder L or R 28.5mm - Peugeot 403
Single piston cylinder with bleeder for front wheel - Peugeot 403 all models - Ø 28.57 mm. Upper left or right mounting - (2 upper cylinders and 2 lower cylinders are needed to equip the front of a 403) - NON CONTRACTUAL photo.
€61.50 TTC
(51,25 € HT)
(51,25 € HT)
Brake clip spring kit - front wheels - Peugeot 403
Brake spring kit for front wheel - Peugeot 403
€22.00 TTC
(22,00 € HT)
(22,00 € HT)
Rear brake cylinder 25.4mm - cone protruding - Peugeot 403
Rear wheel cylinder d 25.4mm, inclined pipe inlet 7/16. Exiting cone visible at the bottom of the liquid inlet on the cylinder.Non contractual photo.
€60.60 TTC
(50,50 € HT)
(50,50 € HT)
Master cylinder 25.4 mm Peugeot 403
Complete master cylinder D 25.4 mm. For Peugeot 403.Piston 1 p or 25.4 mm1/2 output 20 f per inchEntry about 17 mm60 mm center distance for M 8 screwsThere is also a 22 mm model, available on our store.
€64.80 TTC
(54,00 € HT)
(54,00 € HT)
Master cylinder Ø 25.4 mm - Peugeot 403
Repair kit for Ø 25.4 mm master cylinder
€27.00 TTC
(22,50 € HT)
(22,50 € HT)
Brake line - from 0 to 50 cm
Brake line remanufactured on demand only in copper diameter 6.35 mm. Small model, length less than 50 cm. Provide model (length and 2 original tips) Shipping after receipt of your model.
€47.64 TTC
(39,70 € HT)
(39,70 € HT)
Special brake grease tube - Plastilub ATE - 75 ml
Tube of special braking grease (75 ml). ATE's Plastilube is used to lubricate the guide faces on calipers and brake linings and to protect them against corrosion.Note: The friction surfaces of the brake pads must not be coated with ATE Plastilube!
€13.80 TTC
(11,50 € HT)
(11,50 € HT)
